Limelight Frolic

PEEK (Polyether Ether Ketone) is a high-performance polymer used in medical devices and aerospace. It withstands temperatures above 300u00b0C, produces no off-gassing, and is flavor-neutral.

In the Frolic, the entire vapor path u2013 from the heating chamber to the mouthpiece u2013 is made from PEEK. The vapor never touches metal or silicone on its way to your mouth. Combined with 200 mm+ of cooling length, this produces cool, clean vapor at any airflow setting.

• Heat-resistant to 300u00b0C+
• No off-gassing or flavor contamination
• Medical and aerospace certified
• Easy to clean (isopropyl alcohol)

The Frolic can be fully disassembled without tools. Every part – mouthpiece, cooling unit, oven, battery – can be removed, cleaned, or replaced individually.

For users this means: if a part breaks, you replace it – not the whole device. That is a deliberate contrast to the usual disposable electronics.

Oven material: The heating chamber is made from 6000-series aluminum with a hard-anodized non-stick coating. Oven capacity is approximately 0.25 g. The housing combines anodized aluminum with Ultem (PEI) and PEEK high-performance polymers for heat-critical areas.

Dosing capsules: The cooling unit is compatible with Crafty/Mighty-style dosing capsules. This makes pre-packing easy and keeps the oven clean.

Airflow control: Draw resistance is infinitely adjustable from 0 to 25 l/min by rotating the mouthpiece. This lets you switch between a restrictive micro-draw and an open direct-lung hit.

The Frolic runs on a standard 21700 battery with 5000 mAh capacity. It pops out without tools and swaps for a fresh cell in seconds while on the go.

Advantages over built-in batteries:

• No capacity loss after 2u20133 years u2013 just insert a new cell
• Replacement cells cost around u20ac5u201310
• Passthrough charging supported (USB-C)
• No e-waste when the battery ages

Package contents:

The Angled Mouthpiece and Direct Output Adapter are sold separately.

The tool-free design means you can strip the Frolic down and clean it in a few minutes.

Cleaning steps:

1. Remove mouthpiece and cooling unit
2. Take out mesh disks from the oven
3. Soak PEEK parts in isopropyl alcohol (90%+) for 15–30 minutes
4. Wipe the oven with an ISO-soaked cotton swab
5. Let everything dry, then reassemble

Wear parts:

• Mesh Disks: swap every 2–4 weeks
• O-Rings: replace when draw resistance drops
• Cooling Unit: clean regularly, no replacement needed

Warning: Never submerge the electronics or battery in any liquid.

Limelight sells 11 official accessories for the Frolic. Thanks to the modular design, each part can be replaced individually – no need to replace the entire device.

• Limelight Official Website
• Frolic Thermal Extractor Product Page
• Contact & Support
• Limelight on Instagram

The Tinymight 2 uses a stainless steel convection heater with an exceptionally large surface area. Unlike most portable vaporizers, the Tinymight works with pure convection: air is drawn through the heating element during inhalation and then passes through the material.

Benefits of pure convection:

• Better flavor: The large heating surface means lower surface temperatures are needed, resulting in purer taste
• No residual heating: In on-demand mode, heating stops immediately when the button is released
• Even extraction: Hot air flows evenly through the material

The heating element is a spiral-shaped metal structure. Different production runs have used various configurations – some placed inside a glass tube, others inside a metal tube, and some as a free-standing structure with ceramic support rods.

Note: The heater produces a faint noise during operation. This is normal and results from current pulses acting on the lightweight, large-surface heating structure.

The Tinymight 2 uses a replaceable 18650 lithium-ion battery. One Molicel battery is included in the package.

Compatible batteries:

The Tinymight 2 is very powerful and requires high-drain cells. Only the following Molicel models are recommended:

• Molicel P30B (3,000 mAh)
• Molicel P28A (2,800 mAh)
• Molicel P26A (2,600 mAh)

Warning: Other 18650 batteries may provide insufficient performance or pose a safety risk. Only use original batteries or Molicel cells from trusted sources.

Charging:

Charging is done via USB with a cable and an adapter capable of at least 2A output. A full charge from 0 to 90% takes approximately 1.5 hours. The aluminum bottom panel gets warm during charging – this is normal as it acts as a heatsink.

Charging only starts when the battery voltage has dropped sufficiently. If charging doesn't begin, the battery is still too full for a new charging cycle.

The Tinymight 2 offers two operating modes, selectable when turning on the device:

On-Demand Mode:

In on-demand mode, the vaporizer heats only while the button is held down. Upon release, the device returns to standby immediately. Heat-up time is approximately 3 seconds.

• Perfect for single draws between tasks
• No material consumption during standby
• Maximum control over extraction

Session Mode:

In session mode, the vaporizer heats up automatically and maintains a stable temperature until turned off.

• Ideal for longer sessions
• Constant temperature without holding the button
• Easy to pass around in a group

Micro-dosing: The Tinymight 2 works excellently for micro-dosing. The adjustable chamber volume works well with very small amounts as well as larger loads.

Regular cleaning is important for vapor quality and longevity of the Tinymight 2. The parts that need cleaning are the glass tube with cooling unit and occasionally the stainless steel mesh screen above the heater.

Glass tube & cooling unit:

1. Unscrew the threaded ring on the front panel – the internal parts slide out easily
2. Rinse the glass tube and cooling unit with hot water and detergent
3. Alternatively, soak in isopropyl alcohol for stubborn residue
4. Rinse thoroughly and allow to dry completely

Stainless steel mesh screen:

The mesh screen above the heater protects the heating element. If dirty, it can be gently cleaned with the included brush.

Important: The mesh screen must always sit securely in its holder. If it falls onto the heater, it can cause a short circuit that damages the heater. Do not use third-party dosing capsules that could displace the screen.

The Tinymight 2 is handcrafted in Helsinki, Finland. Each unit is individually assembled and assigned a unique serial number.

Materials in the vapor path:

• Stainless steel – heating element and vapor channel
• Quartz glass – glass lining and vapor tube

The entire vapor path uses no glues, chemicals, or insulation materials. The only materials in the device are oak wood, stainless steel, glass, and aluminum. The electronics board is separated from the vapor path.

Counterfeit detection:

Counterfeits exist on the market. Original units from February 2022 onwards have a serial number on the bottom panel and an individually registered security code. In fake TM2 units, the battery is often inserted the opposite way – the original has "+" printed on the inside of the battery lid.

Reduced vapor production:

1. Check the battery: A weak or old battery can reduce performance. Only use recommended Molicel cells.
2. Clean battery lid contact: Occasionally scratch the contact point on the battery lid to ensure optimal power transfer.
3. Adjust calibration: The temperature range can be adjusted in steps from -3 to +3. At +3, setting 7 delivers the results of setting 10.

Cracked glass lining:

The internal glass lining can crack if the unit is dropped. Replacement glass linings are available from the Tinymight shop. Replacement requires a Torx T20 screwdriver. Warning: The internal screw must be loosened before removing the top panel – otherwise the device will be destroyed.

Cooling unit slides out of glass tube:

The cooling unit requires two different o-rings: one 10mm and one 11mm ring. If both are the same size, the fit will be too loose or too tight.

Over 90 official accessories and spare parts are available for the Tinymight 2. Compare prices from 11 European shops in our Tinymight price comparison. The full range is also available directly from the Tinymight EU Shop.

Glass Tubes & Stems:

Mouthpieces:

• Glass Mouthpiece for Ball Stems – fits Long and Short Ball Stem
• Colored Mouthpieces (Pink, Smokey) – glass, for individual style

Dosing Capsules:

• Dosing Capsule v2 – stainless steel, for clean and quick loading
• Dosing Capsule v2 TITANIUM – lighter and more durable
• 5-pack with holder – practical for on-the-go use (stainless steel or titanium)

Water Pipe Adapters:

• 14mm glass adapter – for 14mm water pipes
• 18mm glass adapter – for 18mm water pipes
• 3-in-1 adapter – compatible with various sizes
• Portable Bubbler – compact water filter for on the go

Spare Parts:

• Glass Lining – replacement for cracked linings after drops
• Screen Holder – holds the heater protection screen
• Mesh Screen – protects the heater element
• Tube Holder Threaded Ring – secures the glass tube
• O-rings – sets for cooling unit, ball stems, top panel and multitool

Other Accessories:

• Cooling Unit – most important wear part
• Stir Tool / Multitool – for stirring and emptying the chamber
• Extra Battery + Charger – for unlimited runtime on the go
• USB-C Quick Charger (EU plug) – for fast charging
• Beeswax Jar – for wood surface maintenance
• Bag of Balls – replacement glass balls for ball stems

The Tinymight 2 package includes:

• 1× Tinymight 2 Vaporizer (oak wood body)
• 1× Molicel 18650 battery
• 1× Glass tube with cooling unit
• 1× USB charging cable
• 1× Cleaning brush
• 1× Spare o-rings
• 1× Quick start guide

Note: Additional glass tubes, replacement glass linings, and extra Molicel batteries are available as optional accessories directly from Tinymight.

Choosing the right temperature on the Tinymight 2 determines flavor, vapor density, and active compound profile. Lower temperatures (170–185 °C) emphasize terpenes and deliver mild, aromatic vapor. Higher temperatures (195–210 °C) produce thicker clouds and stronger effects.

Temperature Zones

Practical Tips

• Start at 180 °C and increase in 5-degree steps
• Finer grind often needs 5–10 °C lower temperature
• In cold environments, raise starting temp by 5 °C

• Tinymight Official Website
• Tinymight 2 User Manual (PDF)
• Tinymight FAQ (Manufacturer)
• Warranty Registration & Conditions
• Official Tinymight Retailers
• Tinymight EU Shop – Accessories & Spare Parts