Storz & Bickel Mighty+

At the heart of the Mighty+ is Storz & Bickel's patented heating system combining convection and conduction. The chamber heats from the outside (conduction) while hot air simultaneously flows through the material (convection). This dual approach ensures even extraction from the first draw.

Compared to pure convection vaporizers like the Tinymight 2, the Mighty+ heats up a bit slower (~60 seconds to 180 °C), but vapor production stays consistent throughout the session. Airflow sits at 10 liters per minute — enough for deep draws with minimal resistance.

Booster & Superbooster

A double-click on the power button activates the Booster, raising temperature by 15 °C. This efficiently extracts remaining material near the end of a session without permanently changing the base temperature. Storz & Bickel calls the maximum level "Superbooster" — a practical feature other manufacturers lack.

The Mighty+ uses PEEK (polyether ether ketone) for its housing. PEEK comes from medical and aerospace industries: food-safe, heat-resistant, and far tougher than standard plastic. Where other vaporizers crack after a drop, a PEEK housing survives.

The filling chamber holds 1.4 cm³ and has a ceramic coating for wear resistance and easy cleaning — a damp cotton swab after every third session does the job. The cooling unit sits on top and uses a labyrinth airflow path that brings vapor to a comfortable temperature before it reaches the mouthpiece.

Storz & Bickel manufactures the Mighty+ entirely in Germany and certifies it under UL 8139 and IEC 60335-1 — safety standards rarely seen in the vaporizer industry.

The Mighty+ features an LC display showing current and target temperature simultaneously. Two soft-touch buttons (+/-) adjust temperature in 1-degree steps across a 40–210 °C range. The display reads well even in direct sunlight.

Compared to the VENTY (OLED display, Bluetooth app), the Mighty+ offers leaner app connectivity. Via Bluetooth it connects to the S&B Web App, where you can fine-tune the temperature and install firmware updates. That said, the device works perfectly without any app: two buttons on the display, pick your temperature, wait for the vibration — done.

A vibration alert signals when target temperature is reached. After one minute of inactivity, the Mighty+ shuts off automatically — saving battery and preventing overheating.

App & Firmware Updates

The S&B Web App runs directly in the browser — no app store download needed. After Bluetooth pairing, it shows real-time device temperature and allows precise adjustments. Firmware updates are offered automatically when available and install with one click.

Browser tip: Chrome (desktop and Android) works most reliably since the app uses the Web Bluetooth API. Safari and Firefox have limited or no Web Bluetooth support. On iOS, Bluefy (available in the App Store) provides a Web Bluetooth-capable browser as a workaround.

The Mighty+ houses two lithium-ion batteries totaling 3,300 mAh. In practice, expect 6 to 8 full sessions per charge, depending on temperature and draw behavior. That is less than the VENTY (5,940 mAh) but covers a full day for most users.

Charging runs through USB-C. With the Supercharger (15V / 3A, sold separately), the Mighty+ reaches 80 percent in roughly 40 minutes. Standard USB-C chargers work too, just slower. Passthrough charging is supported — vape while connected to the Supercharger.

At 242 grams and 8.0 × 14.0 × 3.0 cm, the Mighty+ is not a pocket device, but it fits a jacket pocket or small backpack. The weight gives it a premium feel that cheaper vaporizers lack.

The battery is not user-replaceable. Storz & Bickel offers battery replacement as a paid service.

Concentrates with the Mighty+

For waxes and oils, Storz & Bickel offers Liquid Pads – small stainless-steel mesh discs placed inside the filling chamber. The concentrate goes on top of the pad so nothing seeps into the device. A set of 8 costs around €10. The pads also fit inside dosing capsules together with a Concentrate Pad. Recommended temperature for concentrates: 190–210°C.

Battery Life in Practice

Storz & Bickel officially quotes around 90 minutes of use. In daily practice, that translates to 6 to 8 sessions at 180–190 °C. Heavy booster use or sessions above 200 °C bring the count closer to 5 or 6. For comparison, the VENTY with its 5,940 mAh battery lasts notably longer, though it weighs only 120 g less.

The two lithium-ion cells (3,300 mAh total) are permanently installed. When capacity drops after 2–3 years, Storz & Bickel offers paid battery replacement as a service — send the device in and expect it back within about two weeks.

The Mighty+ fully supports dosing capsules. These small stainless steel capsules are pre-filled and inserted as needed — practical on the go and keeps the chamber clean. An 8-capsule magazine is available as an accessory.

Other accessories: Wear & Tear Set (seals, screens, cooling unit parts), Mighty+ Case (hard shell), USB-C Supercharger, and the 14 mm water pipe adapter for bong sessions.

Cleaning

The cooling unit comes off without tools and soaks in isopropyl alcohol. Brush the chamber after each session. Every two to three weeks, Storz & Bickel recommends a thorough clean: disassemble the cooling unit, swap screens, wipe the chamber with a damp swab. The entire process takes under five minutes.

Tip: Collect used dosing capsules and batch-clean them in isopropyl alcohol — saves time and solvent.

Wear Parts & Replacement Costs

Storz & Bickel offers a Wear & Tear Set for around €30. It includes cooling unit parts, seals, screens, and a cleaning brush. Individual parts are also available: replacement screens (normal set, 6 pieces) for about €6, a complete cooling unit for about €18. Screens should be replaced every 3 to 6 months, the cooling unit as needed. Original parts are available from the Storz & Bickel online shop or authorized retailers.

The Mighty+ package includes:

• 1× Mighty+ vaporizer
• 1× USB-C charging cable
• 1× filling chamber tool with cleaning brush
• 3× normal screens + 3× coarse screens
• 1× quick start guide

The Supercharger (fast charger) is not included and must be purchased separately for around €40. Dosing capsules are also sold separately – the 40-capsule magazine with filling aid costs about €30.

Regular cleaning keeps the Mighty+ performing at its best and ensures pure flavor. Brush out the chamber after every session to remove loose residue. Clean the mouthpiece and vapor path weekly with isopropyl alcohol (90% or higher).

Cleaning Schedule

Common Mistakes to Avoid

• Never use water inside the chamber — only isopropyl or dry cleaning
• Do not use sharp metal tools in the vapor path
• Replace screens when draw resistance increases

Choosing the right temperature on the Mighty+ determines flavor, vapor density, and active compound profile. Lower temperatures (170–185 °C) emphasize terpenes and deliver mild, aromatic vapor. Higher temperatures (195–210 °C) produce thicker clouds and stronger effects.

Temperature Zones

Practical Tips

• Start at 180 °C and increase in 5-degree steps
• Finer grind often needs 5–10 °C lower temperature
• In cold environments, raise starting temp by 5 °C

The Mighty+ battery lasts several sessions with typical use. For maximum lifespan, keep the battery between 20% and 80% and avoid deep discharge. USB-C charging with a quality power adapter speeds up charging.

Battery Tips

• Do not leave on the charger permanently — unplug after 100%
• For replaceable batteries: use original or recommended cells
• Battery performance drops in cold — let it warm up before sessions
• Pass-through charging (if supported) allows use while charging

Both by Storz & Bickel with identical hybrid heating (210°C). The Mighty+ has a larger display and more battery. The Crafty+ is more compact and ~30 EUR cheaper but needs the app for full control.

• STORZ & BICKEL Support – MIGHTY+
• STORZ & BICKEL – Cleaning Guide
• MIGHTY+ Parts & Accessories
• Warranty Registration (+1 Year)