Tinymight 2

The Tinymight 2 features an analogue temperature adjustment dial on the bottom of the device. It offers 10 main settings with intermediate positions, giving a total of around 20 different temperature levels in the range from 120 to 240°C.

The electronics regulate the heater in real time with high precision. The set temperature is maintained reliably, regardless of draw strength.

Calibration:

If the standard temperature range is not ideal, the Tinymight 2 can be calibrated in steps from -3 to +3 relative to the factory settings. When calibrated to +3, setting 7 delivers the same result as setting 10 normally would. Full instructions can be found in the Tinymight 2 Manual (PDF).

Note: The Tinymight cannot be switched on if the adjustment dial is below setting 2 – this is a safety mechanism against accidental activation.

The Tinymight 2 uses a stainless steel convection heater with a particularly large surface area. Unlike most portable vaporizers, the Tinymight works with pure convection: the air is drawn through the heating element during inhalation and only then passes through the material.

Advantages of pure convection:

• Better flavour: Because of the large heating surface, the surface temperature does not need to be as high, which leads to cleaner flavour
• No residual heating: In on-demand mode, heating stops immediately when the button is released
• Even extraction: The hot air flows through the material evenly

The heating element is a spiral-shaped metal structure. Different versions were used in different production batches – sometimes in a glass tube, sometimes in a metal tube, and sometimes as a freestanding structure with ceramic support rods.

Note: The heater makes a quiet noise during operation. This is normal and results from the current pulses acting on the light, large-surface heating structure.

The Tinymight 2 uses a replaceable 18650 lithium-ion battery. A Molicel battery is included in the box.

Compatible batteries:

The Tinymight 2 is very powerful and requires high-drain cells. Only the following Molicel models are recommended:

• Molicel P30B (3.000 mAh)
• Molicel P28A (2.800 mAh)
• Molicel P26A (2.600 mAh)

Warning: Other 18650 batteries may provide insufficient power or pose a safety risk. Use only genuine batteries or Molicel cells from trustworthy sources.

Charging:

Charging takes place via USB with a cable and an adapter with at least 2A output current. A full charge from 0 to 90% takes around 1.5 hours. During charging, the aluminium bottom panel becomes warm – this is normal, as it acts as a heat sink.

Charging only starts once the battery voltage has dropped sufficiently. If charging does not begin, the battery is still too full for a new charging cycle.

The Tinymight 2 offers two operating modes, which are selected when switching it on:

On-demand mode:

In on-demand mode, the vaporizer heats only while the button is being pressed. When released, the device immediately returns to standby. Heat-up time is only around 3 seconds.

• Perfect for occasional single draws
• No material consumption in standby
• Maximum control over extraction

Session mode:

In session mode, the vaporizer heats automatically and maintains a stable temperature until it is switched off.

• Ideal for longer sessions
• Constant temperature without holding a button
• Easy to pass around in a group

Microdosing: The Tinymight 2 is excellent for microdosing. The adjustable chamber size works both with very small and with larger amounts.

Regular cleaning is important for vapour quality and the longevity of the Tinymight 2. The parts that need cleaning are the glass tube with cooling unit and occasionally the stainless steel screen above the heater.

Glass tube & cooling unit:

1. Unscrew the threaded ring on the front plate – the inner parts can then be pulled out easily
2. Rinse the glass tube and cooling unit with hot water and washing-up liquid
3. Alternatively soak them in isopropyl alcohol for stubborn residue
4. Rinse thoroughly and allow to dry completely

Stainless steel screen:

The screen above the heater protects the heating element. If it is dirty, it can be carefully cleaned with the cleaning brush.

Important: The screen must always sit securely in its holder. If it comes loose and falls onto the heater, it can cause a short circuit that damages the heater. Do not use third-party dosing capsules that could shift the screen.

The Tinymight 2 is handcrafted in Helsinki, Finland. Each device is assembled individually and given a unique serial number.

Materials in the vapour path:

• Stainless steel – heating element and vapour channel
• Quartz glass – glass lining and vapour tube

No adhesives, chemicals or insulating materials are used anywhere in the vapour path. The only materials in the device are oak wood, stainless steel, glass and aluminium. The electronics board is separated from the vapour path.

Counterfeit detection:

Counterfeits exist on the market. Original devices from February 2022 onwards have a serial number on the bottom panel and an individually registered security code. On TM2 counterfeits, the battery is often inserted the wrong way round – on the original, a "+" is shown on the inside of the battery cap.

Reduced vapour production:

1. Check the battery: A weak or old battery can reduce performance. Use only recommended Molicel cells.
2. Clean the battery cap contact: Occasionally scrape the contact point on the battery cap clean for optimal power transfer.
3. Adjust calibration: The temperature range can be adjusted in steps from -3 to +3. At +3, setting 7 delivers the results of setting 10.

Broken glass lining:

The inner glass lining can break if the device is dropped. Replacement glass linings are available in the Tinymight shop. Replacement requires a Torx T20 screwdriver. Caution: Before removing the top panel, the inner screw must be loosened – otherwise the device will be destroyed.

Cooling unit slips out of the glass tube:

The cooling unit requires two different O-rings: one 10mm ring and one 11mm ring. If both are the same size, it will fit either too loosely or too tightly.

There are over 90 official accessories and spare parts for the Tinymight 2. Prices from 11 European shops can be found in our Tinymight price comparison. The full range is also available directly from the Tinymight EU shop.

Glass tubes & stems:

Mouthpieces:

• Glass mouthpiece for Ball Stems – fits Long and Short Ball Stem
• Coloured mouthpieces (Pink, Smokey) – made of glass, for an individual style

Dosing capsules:

• Dosing Capsule v2 – made of stainless steel, for clean and quick filling
• Dosing Capsule v2 TITANIUM – lighter and more durable
• Set of 5 with holder – practical for travel (stainless steel or titanium)

Water pipe adapters:

• 14mm glass adapter – for 14mm water pipes
• 18mm glass adapter – for 18mm water pipes
• 3-in-1 adapter – compatible with various sizes
• Portable Bubbler – compact water filter for travel

Spare parts:

• Glass lining (Glass Lining) – replacement if broken after a drop
• Screen holder (Screen Holder) – holds the heater protection screen
• Heater protection screen (Mesh Screen) – protects the heater
• Threaded ring (Tube Holder Threaded Ring) – holds the glass tube
• O-rings – sets for the cooling unit, Ball Stems, top panel and multitool

Other accessories:

• Cooling unit (Cooling Unit) – the most important wear part
• Stir Tool / Multitool – for stirring and emptying the chamber
• Extra battery + charger – for unlimited runtime on the go
• USB-C fast charger (EU plug) – for fast charging
• Beeswax jar – for caring for the wood surface
• Bag of Balls – replacement glass beads for Ball Stems

Included with the Tinymight 2:

• 1× Tinymight 2 vaporizer (oak wood housing)
• 1× Molicel 18650 battery
• 1× glass tube with cooling unit
• 1× USB charging cable
• 1× cleaning brush
• 1× spare O-rings
• 1× short user guide

Note: Additional glass tubes, replacement glass linings and further Molicel batteries are available directly from Tinymight as optional accessories.

The right temperature on the Tinymight 2 determines flavour, vapour density and active compound profile. Lower temperatures (170–185 °C) emphasise terpenes and deliver mild, aromatic vapour. Higher temperatures (195–210 °C) produce denser clouds and a stronger effect.

Temperature zones at a glance

Practical tips

• Start at 180 °C and increase in 5-degree steps
• A finer grind often requires a temperature 5–10 °C lower
• In cold surroundings, increase the starting temperature by 5 °C

• Tinymight Official Website
• Tinymight 2 User Manual (PDF)
• Tinymight FAQ (Manufacturer)
• Warranty Registration & Conditions
• Official Tinymight Retailers
• Tinymight EU Shop – Accessories & Spare Parts