The Solo 3 heats up in 5-15 seconds, depending on the target temperature. At 193°C, it takes around 10-12 seconds. That is twice as fast as the Solo 2 (30 seconds).
What is the difference between Session mode and On-Demand mode?
In Session mode, you get a continuous 5-20-minute session at a constant temperature. In On-Demand mode, you start each inhalation individually - the device heats up, you draw, then it cools down. On-Demand preserves your material between draws.
How many draws do I get from one load?
With an XL stem at 193°C, you get 4-6 strong draws in Session mode. In On-Demand mode, it is 2-5 draws per load, depending on the heat level. The regular stems hold about half that.
Can I use the XL stems with the Solo 2 as well?
Technically yes, but it makes little sense. The Solo 2 heating chamber is shallower, so the herb in XL stems sits too close to the seal, where there is no heat. On the Solo 3, the chamber is deeper - XL stems work perfectly.
How long does the battery last?
Arizer advertises up to three hours of use per charge. Actual runtime depends on mode, temperature and session length. The internal battery is not user-replaceable; Arizer offers a replacement service.
Which temperature is best?
193°C (380°F) is the sweet spot according to users and reviews. Below that, the AVB stays just brown; above it, the bottom turns blackish. At 193°C, you get maximum flavour, dense clouds and clean AVB.
Can I use the Solo 3 with a water pipe?
Yes, two WPA stems (regular + XL) are included. They fit 14mm bubblers. The display rotates automatically when you turn the device upside down. On-Demand mode is ideal for water pipes.
How do I clean the glass stems?
Empty the stems immediately after the session while they are still warm. Clean the screen holes with a brush. For deeper cleaning: soak the stems in isopropyl alcohol, then rinse with warm water.
Is the Solo 3 pocket-friendly?
At 280 g and 130 mm tall, Solo 3 V2 is better carried in a bag or jacket than in a tight trouser pocket. The body measures 49 × 32 × 130 mm, and the glass tube also needs protection in transit.
Can I vape while charging?
Yes, pass-through charging is supported. You can keep the Solo 3 plugged in via USB-C and use it at the same time. It is not the best thing for the battery, but it works.
What does 80/20 hybrid heating mean?
80% of the heating is done by convection (hot air while drawing), 20% by conduction (contact with the warm glass). The conduction keeps the glass preheated, while convection extracts during the draw. That is the ideal balance.
How much herb fits in the stems?
The regular stems hold about 0.1g, while the XL stems hold about 0.2g. The XL version has double the capacity and accordingly delivers more vapour and effect per session.
The Solo 3 heats up in 5-15 seconds, depending on the target temperature. At 193°C, it takes around 10-12 seconds. That is twice as fast as the Solo 2 (30 seconds).
What is the difference between Session mode and On-Demand mode? +
In Session mode, you get a continuous 5-20-minute session at a constant temperature. In On-Demand mode, you start each inhalation individually – the device heats up, you draw, then it cools down. On-Demand preserves your material between draws.
How many draws do I get from one load? +
With an XL stem at 193°C, you get 4-6 strong draws in Session mode. In On-Demand mode, it is 2-5 draws per load, depending on the heat level. The regular stems hold about half that.
Can I use the XL stems with the Solo 2 as well? +
Technically yes, but it makes little sense. The Solo 2 heating chamber is shallower, so the herb in XL stems sits too close to the seal, where there is no heat. On the Solo 3, the chamber is deeper – XL stems work perfectly.
How long does the battery last? +
Arizer advertises up to three hours of use per charge. Actual runtime depends on mode, temperature and session length. The internal battery is not user-replaceable; Arizer offers a replacement service.
Which temperature is best? +
193°C (380°F) is the sweet spot according to users and reviews. Below that, the AVB stays just brown; above it, the bottom turns blackish. At 193°C, you get maximum flavour, dense clouds and clean AVB.
Can I use the Solo 3 with a water pipe? +
Yes, two WPA stems (regular + XL) are included. They fit 14mm bubblers. The display rotates automatically when you turn the device upside down. On-Demand mode is ideal for water pipes.
How do I clean the glass stems? +
Empty the stems immediately after the session while they are still warm. Clean the screen holes with a brush. For deeper cleaning: soak the stems in isopropyl alcohol, then rinse with warm water.
Is the Solo 3 pocket-friendly? +
At 280 g and 130 mm tall, Solo 3 V2 is better carried in a bag or jacket than in a tight trouser pocket. The body measures 49 × 32 × 130 mm, and the glass tube also needs protection in transit.
Can I vape while charging? +
Yes, pass-through charging is supported. You can keep the Solo 3 plugged in via USB-C and use it at the same time. It is not the best thing for the battery, but it works.
What does 80/20 hybrid heating mean? +
80% of the heating is done by convection (hot air while drawing), 20% by conduction (contact with the warm glass). The conduction keeps the glass preheated, while convection extracts during the draw. That is the ideal balance.
How much herb fits in the stems? +
The regular stems hold about 0.1g, while the XL stems hold about 0.2g. The XL version has double the capacity and accordingly delivers more vapour and effect per session.
To provide the best experiences, we use technologies like cookies to store and/or access device information. Consenting to these technologies will allow us to process data such as browsing behavior or unique IDs on this site. Not consenting or withdrawing consent, may adversely affect certain features and functions.
Functional
Always active
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
Preferences
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
Statistics
The technical storage or access that is used exclusively for statistical purposes.The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
Marketing
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.
Comments
No comments yet. Be the first!
Sign in to comment